Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is a manufacturer of gas-liquid two-phase flow and electric auxiliary equipment such as continuous discharge expansion vessels. The agreement is applicable to the self-adjusting liquid level controller of the gas-liquid two-phase flow of the N125 continuous discharge expansion vessel in a thermal power plant. It proposes technical requirements in terms of energy and experimentation. This agreement proposes minimum technical requirements, and the supplier provides gas-liquid two-phase flow manufacturing and corresponding services that comply with the requirements of this agreement and industrial standards. If the demand party has any special requirements other than this agreement, they shall be proposed in writing and agreed upon by both the supply and demand parties. This technical agreement, as an attachment to the purchase contract, has the same legal force as the main text of the contract.

2. Design parameters

2.1 It is a self regulating liquid level controller for continuous discharge of gas-liquid two-phase flow

Hydrophobic capacity: 6t/h

Hydrophobic temperature; 170 ℃

Positive pressure: 0.6~0.8MPa

(Steam side pressure below -: 0.2MPa)

Drain pipe diameter: Ф 89 mm

2.2 The second continuous discharge uses a steam liquid two-phase flow self regulating liquid level controller

Hydrophobic capacity: 6t/h

Hydrophobic temperature; 110 ℃

Positive pressure: 0.2~0.3MPa

(Steam side pressure below -: 0.05MPa)

Drain pipe diameter: Ф 89 mm

3. Specifications and standards for gas-liquid two-phase flow in equipment

The supplier shall design and manufacture according to the standards of gas-liquid two-phase flow and industry standards.

4. Technical requirements for gas-liquid two-phase flow

4.1 The continuous drainage flow rate can be fully automatically adjusted within the range of 6t/h ± 50%.

4.2 Spray nozzle material: 1Cr18Ni9Ti

5. Other requirements for gas-liquid two-phase flow

5.1 All gas-liquid two-phase flow outer surfaces should be treated with appropriate methods and painted. The primer should be applied before the equipment rusts, and the surface paint should be applied after the primer is dry.

5.2 Transportation and storage measures for gas-liquid two-phase flow

The gas-liquid two-phase flow must be completely dry during transportation, and all openings and flange interfaces must be protected to prevent damage, corrosion, or entry of impurities.

6. Supply scope of gas-liquid two-phase flow

Item Name Model Specification Unit Quantity Remarks

1. Self regulating liquid level controller

(Supporting signal regulator) SWQ-IV (80) units 2

(Equipped with interface counter flanges and fasteners)

2 Self regulating liquid level controller

(Supporting signal regulator) SWQ-IV (80) units 2

(Equipped with interface counter flanges and fasteners)

你可能喜歡看：

installation and working engineering of coal powder sampler

11-25 1021

The installation and operation of the coal powder sampler and mobile coal powder sampler of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. drill holes on the flue, extend the sampling tube into the flue, and make the sampling head face the direction of the incoming smoke flow.

squirting air extractor

08-20 932

Assembly and installation of oil injectors

11-25 924

The oil supply and lubrication oil injectors are completely identical in structure, mainly composed of orifice nozzles, diffusion tubes, sleeves, filters, etc.

The function of an oil injector is to use a small amount of lubricating oil as power

08-20 870

The function of the oil injector of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is to use a small amount of lubricating oil as power, suck in a large amount of oil, and supply lubricating system and main oil pump with oil at a certain pressure.

The principle of steam jet pump and steam injector

11-25 859

A steam injector is a device that is powered by steam and is needed in modern engineering. It does not require electricity, has no moving or rotating parts, is simple in system, and works reliably, so it is used.

The basic principle of lubricating oil system injectors

11-25 813

The oil injector is composed of a nozzle, a filter screen, an expansion pipe, and an inlet pipe. in addition to supplying the inlet oil of the centrifugal main oil pump, it also supplies lubricating oil system and sealing oil system oil.

Portable constant velocity fly ash sampler for regular coal powder sampling on the air and coal powder pipeline

08-20 783

The portable constant velocity fly ash sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd., also known as the fly ash constant velocity sampler or the swirling fly ash constant velocity sampler,

Working status of oil injector and main oil pump

11-25 771

The working status of the oil injector and main oil pump, the analysis of the reasons for the drop in the inlet oil pressure test of the main oil pump of a 200MW steam turbine, and the composition of the oil supply system of the 200MW steam turbine generally adopt a centrifugal main oil pump oil supply system with dual injectors.

Working principle of automatic steam liquid two-phase flow trap

11-25 732

The automatic steam liquid two-phase flow steam trap, also known as the gas-liquid two-phase flow control valve, is suitable for the water level self operated intelligent control of pressure vessels such as high and low pressure heaters, continuous discharge expansion vessels, raw water heaters, and heating network heaters in the power industry.

The functions of lubrication oil tank injector 1 # and injector 2 # for steam turbines

11-25 698

The oil injectors produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd. generally consist of nozzle filters, expansion pipes, inlet pipes, etc., and are installed on the main oil pump.

• Previous：Structure of water level control device and working principle of gas-liquid two-phase flow
• Next：Structural form of coal powder sampler